How to Install a Ghost Immobiliser
Ghost immobilisers are hidden security device that protects your car from hacking and key cloning. It works by stopping the engine from running unless it is started using PIN codes, which can be up to 20 characters in length.
This extra layer of protection isn't visible to thieves who might not be expecting it. Some systems have an app which allows the owner to disable their immobiliser in the event of forgetting their PIN number or utilize the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is a cutting-edge security system, is able to be integrated directly into the ECU of your vehicle. It offers a discrete protection against thieves. It is highly efficient and user-friendly, making it a valuable option to add to your vehicle's security arsenal. But, as with any other anti-theft device, it is not 100% reliable and requires regular maintenance to ensure its operation. This guide will help you make the most of your Ghost 2 immobiliser .
CAN (Controller Area Network) is a robust serial network that lets microcontrollers communicate with each other in short distances, without the need for a central control unit. It is designed to multiply electrical wiring in vehicles, which saves on copper. It has many advantages including low cost and easy use.
The CAN protocol is used in most modern automobiles to connect with the engine management system, transmission controller, steering control module and air conditioning controls and more. It also carries sensor data including speed sensors and inputs, to control the various functions of the car. The CAN bus is used to monitor these different components, and can prevent the vehicle from starting if they are in a dangerous state.
It's crucial to understand how the CAN bus functions and how it is secured. It is possible to add additional features to vehicles using CAN bus, however it is important to protect it from threats from hackers and other types. Installing a firewall and monitoring your CAN-bus with software is the best way to do this.
Ghost2's discrete control unit is hidden within the car's dashboard or wiring harness, which prevents thieves from physically tampering with it. It's also impossible to reset the PIN or emergency code without access to the vehicle.
If you need to surrender your vehicle to a valet parking service, maintenance or for any other reason, you can activate the Transport Mode. This feature turns off both the keyfob as well as the ignition functions of the Ghost immobiliser. It will only be activated after the vehicle has travelled 31 mph over a period of 15 minutes.
How do I create a PIN code
The Ghost immobiliser shields your vehicle from theft. The cutting-edge technology uses an PIN code to disable the engine and prevent it from starting without the correct code or an authorized fob or mobile device. Its discrete design ensures the system is not noticed and offers unbeatable security against theft. Furthermore, the system is TASSA certified and can provide significant savings on car insurance premiums.
During installation when you install the Ghost system enters an learning mode that records the sequence of buttons pressed to create your unique pin code. After the pin code is created the installer will guide you through the process of activating the system. Once activated, the Ghost system shuts down the vehicle's start motor until you enter a valid PIN or switch the vehicle to transport mode. This makes it difficult for thieves or cloners who want to hack or clone your vehicle's starter system.
Installing an Ghost immobiliser is easy, but it is important to follow the specific instructions in the user's manual to ensure proper operation. Multimeters and basic hand tools can be used to check electrical values. Insulation tape and heat shrink tubing can protect exposed wiring Cable ties are essential for keeping everything tidy and secure. Test the system on regular basis to identify any issues that could be.
It is essential to test the system one more time before turning on the ignition. The Ghost immobiliser will arm itself after 3 to 30 seconds, based on the car's model. The system is also fitted with a Service/Valet Mode which allows you to temporarily remove the system for servicing or valet parking.
The immobiliser should be hidden in a discreet location beneath the steering wheel or on the dashboard. It is recommended to use a small bit of paint or duct tape to mark the CAN H and CAN L wires to ensure that you easily find them when you are testing. In addition, the CAN H and CAN L wires must be connected to a power source that provides constant 12V. It is crucial to verify the connections again after testing, as an incorrect identification of these wires may cause the system malfunction.
Activating the system
A ghost immobiliser stops your car from starting when you press a few buttons on the vehicle, typically on the steering wheel or the door panel, or the central console. The sequence can be altered by the user at any time. Once the system is activated it is in no way able to be removed by thieves, making it a good option for anyone who wishes to secure their vehicle from theft.
The device is not designed to be detected by modern diagnostic tools and code-grabbing technology. It does not emit radio frequency either which makes it more difficult for thieves to find.
If the device is discovered, it will stop the engine from running. It will also sound an alarm to scare thieves away. The device can be used to track a car's location, which will aid in the search for the vehicle in the event that it has been stolen.
Contact Car Specalist Customs for a estimate or to discuss your options in an immobiliser that is ghost-like. We are fully qualified to install a ghost immobiliser for your vehicle, and will make sure it is concealed in a hard-to-reach area. We can also install other security measures, such as a kill switch and wheel lock, to ensure your vehicle is secure from thieves.
Disarming the System
It is important to know how to disarm a Ghost immobiliser if fitted to your car. This will assist you in the case that you lock your keys in the car or if your battery fails. The system has a unique PIN code that only you know. It won't be able to start the car without this code. Pressing the combination buttons on the steering wheel or on the dashboard is the most efficient method to enter your code. This is much simpler than using a key fob and prevents others from copying the remote.
In contrast to some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and works with your vehicle's CAN bus network to function. Its standout feature is its ability bypass the engine without affecting your vehicle's normal functions, making it hard for thieves to use signal boosters or clone your car key. It does not emit radio frequency, therefore thieves won't be able to detect it.
The Ghost system comes with a Transport Mode which allows you to temporarily disable security in situations like transportation or service. This feature is great for when you're loaning your vehicle to someone else without sharing your PIN code or if your vehicle requires to be protected even while you drive it. Press the service button five times over two seconds to enable Transport Mode. The Ghost system will confirm activation by giving 5 signal indicators.
Save the emergency code in your vehicle in a safe location. If you ever get locked out of your vehicle, you can call the technician or the company that installed the system, and they will give you the code. If you are unable to reach them then you can attempt to contact an authorized dealer however this will require verification procedures and could result in additional fees.
This system isn't just useful, but it will also protect your vehicle from theft and lower cost of insurance. Many insurance companies offer lower costs or financial incentives for those who install this system to prevent theft.